Logger Pro requires approximately 200/380 MB (Mac/Windows) disk storage.GW-TEMP is not supported on Windows 10 version 1703 (Creators Update) or newer as the Windows Bluetooth technology stack was completely redesigned by Microsoft in that release. Mac users of GW-TEMP requires 10.10 or newer GW-TEMP is not supported on Mac prior to 10.10 nor on Windows prior to Windows 10. Go Wireless Temperature (GW-TEMP) requires Windows 10 (version 1607) and a compatible Bluetooth 4.0 transceiver for the computer. We recommend that Mac users use 10.12 or better and upgrade their systems through Apple's software update on a regular basis for the optimal experience in using Logger Pro. Windows 7 (fully updated and with the following Hotfix from Microsoft: us/kb/2921916 installed), 1 GHz or better, 1 GB RAM (2 GB for 64-bit systems), available USB or serial port, Windows 8.1 (8.0 is no longer supported by new Logger Pro releases), or Windows 10 with 4 GB RAM (32 or 64 bit) with OS compatible hardware. Logger Pro installer warns that Windows can't verify the publisher of this driver software.Logger Pro 3 Release Notes Version 3.15 ApContents System Requirements Install Notes What's Changed in Logger Pro 3.15 Logger Pro 3.15 Known Issues File Compatibility Logger Pro 3 Change History What Changed from Logger Pro 2 to Logger Pro 3 LabPro Operating System Changes LabQuest Operating System Changes System Requirements Basic data collection or graphing, without video Contact Vernier Software Technical Support at 888.837.6437 or if you need an interface repaired. If you have multiple interfaces and cables, systematically try to identify if there is an issue with a particular cable or interface. If you can’t find the interface anywhere in the Device Manager, it could be that there is a hardware issue with either the interface or the cable that you are using to connect the interface to the computer. In either case, install the latest version of Logger Pro or Logger Lite. This normally only happens if the software wasn’t installed at all, or if you are installing older versions of Logger Pro (pre-v3.14.1) or Logger Lite (pre-v1.9.3) after Aug 20, 2017. Is the interface listed in Other Devices or do you see an Unknown Device that comes and goes as you plug/unplug the interface? If the interface is listed in either of those sections, see:Ĭonverting from Jungo to WinUSB drivers manually If you have the correct driver installed and are still unable to connect to Logger Pro or Logger Lite, contact Vernier Technical Support at 888.837.6437 or you don’t see Vernier WinUSB Bulk Sys Devices in the Device Manager:ĭo you have a Jungo or VSTJungo section in the Device Manager? Note: The Vernier WinUSB Bulk Sys Devices section is only visible when the interface is connected to the computer. Click the little triangle next to the Vernier WinUSB Bulk Sys Devices to drop down the menu and find out if the driver is located in this section. If the drivers are installed correctly, they will be displayed in the Vernier WinUSB Bulk Sys Devices section. What version of Windows am I running? Is it 32 bit or 64 bit? Instructions for opening System Properties are: You can open the Device Manager from the left pane of System Properties. To identify if the correct drivers are installed on the computer, use the Windows Device Manager. Multiple drivers can be installed on your computer, but only one of them will work with the latest versions of Logger Pro and Logger Lite. Windows Pre-Logger Pro 3.11 original LabQuest and LabQuest Mini, and pre-3.12 LabPro drivers See:Īre the LabQuest 2 device drivers installed correctly? Also, if you have an older version of Logger Pro or Logger Lite, the drivers may be different. Important notes: There are other Vernier interfaces that use other drivers they aren’t covered in this information (e.g., LabQuest 2). The information below is relevant if using specific Vernier interfaces (LabPro, original LabQuest, LabQuest Mini, and LabQuest Stream) connected to a Windows computer running Logger Pro (3.14.1 or newer) or Logger Lite (v1.9.3 or newer).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |